Air has a heat capacity of about 700 Joules per kg per °K and a density of just 1.2 kg/m 3, so its initial energy would be 700 x 1 x 1.2 x 293 = 246,120 Joules — a tiny fraction of the thermal energy stored in the water. 1 watt is approximately 3.412 BTU per hour. One thousand cubic feet (Mcf) of natural gas equals 1.037 MMBtu, or … It goes on the right side. Of course, a change in temperature or pressure will bring about a change in the air itself, but at the standard conditions mentioned above, we can derive two factors, which are: 1. To get the sensible load in Btu/hr by entering the air flow rate in cfm (cubic feet per minute), the other variables should have the below specified units. Standard Cubic Foots to Btu (th)s Conversion. In accordance with the above, units like J/m³, J/L, kcal/m³, BTU/ft³ are used to measure … The best I found with my search is that it takes about 0.005 watts to heat up a cubic foot of air by 1 degree F. However I'm not sure if that power increases linearly - i.e. 3412 Btu/kW Where: CFM = Volume in cubic feet per minute Lbs/ft3 = Density of air or gas at initial temperature Cp = Specifi c heat of air or gas at initial temperature ΔT = Temperature rise in °F SF = Suggested Safety Factor For quick estimates of air heating require-ments for inlet temperatures up to 120°F, the following formula can be used. Of course, to end up with BTU per hour on one side and cubic feet per minute on the other, we need to throw in a factor of 60. scf stands for standard cubic foots and Btu (th) stands for btu (th)s. The formula used in standard cubic foots to btu (th)s conversion is 1 Standard Cubic Foot = 2.72130173187326 Btu (th). 2. BTU is often used as a … Latent heat of water vapour = 1094 Btu/lb at atmospheric pressure and 7 5 o F 75^{o} F 7 5 o F 1 BTU = 1,055 joules, 252 calories, 0.293 watt-hour or the energy released by burning one match. Also on the right side, we have ρc , the density of air times the specific heat of air (at constant pressure, but that's another discussion). Sea water is slightly more dense, but we will ignore that. The density of air at 15°C and sea level is 1.225 kilogram per cubic meter. mass flow rate in lb/ft3-hr, Latent heat of water in Btu/lb. Therefore, 100 cubic feet (Ccf) of natural gas equals 103,700 Btu, or 1.037 therms. The volumetric energy density is measured in units of energy per unit of volume, for example, in joules per cubic meter (J/m ³) or BTU per cubic foot (Btu/ft³). Air will have a Density of 0.075 lbs. The density of water is 1,000 kilograms/m³. The specific heat for water is 4.1813 j/g/C or 1 calorie/g/C. Specific Heat of Liquid, Btu/LB at 60°F 0.63 n/a Cubic Feet of Vapor per Gallon at 60°F 36.38 n/a Cubic Feet of Vapor per Pound at 60°F 8.66 23.55 Specific Gravity of Vapor (Air = 1.0) at 60°F 1.5 0.6 Ignition Temperature in Air, °F 920–1,120 1,301 Maximum Flame Temperature in Air, °F 3,595 2,834 Cubic Feet of Air Required to Consider for a moment two side-by-side cubic meters of material — one cube is water, the other air. Air will have a Specific Heat of 0.24 BTU’s. In other words, 1 standard cubic foot is 3 times bigger than a btu (th). It goes on the right side. In 2019, the U.S. annual average heat content of natural gas delivered to consumers was about 1,037 Btu per cubic foot. per cubic foot. It is approximately the energy needed to heat one pound of water by 1 degree Fahrenheit. 0.01 watts to increase it by 2 degrees F. 0.015 watts for 3 degrees etc - as it would translate to just 0.25 watts to heat up 1 cubic foot of air by 50 degrees F (not C).